Bundle 4 x iPower iBM3508Q 620KV + 4 x ESC

$150.00

4 x iPower iBM3508Q 620KV

In stock

4 x iPeaka SK30A w/SimonK firmware

In stock
Category:

Description

iPower iBM3508Q 620KV w/45cm long cable
iPower Q-series brushless motors are designed specifically for use in multi rotor aircraft. iPower motors are constructed of quality components, making them a smooth, powerful, and efficient motor for your multicopter application. The iBM-Q series motor features 450mm long motor wires and 3.5mm male gold bullet connectors pre-installed. Also included is an accessory package with mount plate, bolt-on style prop adapter, and a set of female 3.5mm gold bullet connectors for your ESC.
iPower iBM3508Q 620KV w/45cm long cable
 
Specs:
Kv: 620rpm
Can size: 45mm
Shaft: 4.0mm (includes prop adapter for 5mm prop mounting)
Motor Mount Holes: 16mm / 19mm
Suggested ESC: 30A
Rated Watts: 180W
Weight: 79g
Cell count: 3~4S Lipoly

Motor wire length: 450mm

iPower iBM3508Q 620KV w/45cm long cable
iPower Q-series brushless motors are designed specifically for use in multi rotor aircraft. iPower motors are constructed of quality components, making them a smooth, powerful, and efficient motor for your multicopter application. The iBM-Q series motor features 450mm long motor wires and 3.5mm male gold bullet connectors pre-installed. Also included is an accessory package with mount plate, bolt-on style prop adapter, and a set of female 3.5mm gold bullet connectors for your ESC.
iPower iBM3508Q 620KV w/45cm long cable
 
Specs:
Kv: 620rpm
Can size: 45mm
Shaft: 4.0mm (includes prop adapter for 5mm prop mounting)
Motor Mount Holes: 16mm / 19mm
Suggested ESC: 30A
Rated Watts: 180W
Weight: 79g
Cell count: 3~4S Lipoly

Motor wire length: 450mm

iPeaka SK30A w/SimonK firmware
If you are looking for a reliable, fast esc for your multicopter, look no further.Flashed with the famous SimonK firmware for super fast linear throttle response.All our ESC`s have external oscillators and use only N-Channel FETs.The external oscillator provides more consistent timing signal and steadier motor speeds, while the N-channel FETs have the advantage of lower resistance, less losses and hence more efficiency.Up to 450hz input rate is supported with immediate translation of input PWM duty into motor control.The boot loader is enabled during the initial flash, so each firmware update from now on can be achieved by a USB linker.All ESC`s are tested before and after the firmware update.

Please note:These esc`s DO NOT monitor the battery voltage. A Lipo alarm or a telemetry system should be used for that purpose.

iPeaka SK30A w/SimonK firmware

Features of the iPeaka SK series Speed Controllers include:

• Extremely low output resistance for efficient operation

• 3-stage protection: Low Voltage Cutoff, Over-Heat Protection & Signal Lost

• 3 Start Modes available: Normal, Soft and Very Soft

• Adjustable Throttle Endpoints to match virtually all transmitter models

• Smooth linear throttle operation for precise control

• High RPM capability: 210,000 (2-pole), 70,000 (6-pole), 30,000 (14 pole)

Specifications of the iPeaka SK 30 Amp Speed Controller:

Input Voltage ………………… 6-18.8 VDC, 2-4 Li-Po cells

Input  rate range…………….  50-400Hz

Output Current ………………. 30 Amps Continous, 40 Amps Burst (10 Sec.)

BEC Output …………………. 5.0 Volts at 3 Amps

Dimensions …………………… 48 x 26 x 11 mm

Weight …………………………. 28g

Package included:

  • 4 x iPeaka SK 30A ESC
  • 4 x iPower iBM3508Q 620KV

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Related products