Bundle 4 x iPower iBM2212Q 1000KV + 4 x ESC

$120.00

4 x iPower iBM2212Q 1000KV

In stock

4 x iPeaka SK22A w/SimonK firmware

In stock
Category:

Description

iPower iBM2212Q 1000KV

iPower Q-series brushless motors are designed specifically for use in multi rotor aircraft. iPower motors are constructed of quality components, making them a smooth, powerful, and efficient motor for your multicopter application. Each 2212 motor features 450mm long motor wires and 3.5mm male gold bullet connectors pre-installed. Also included is an accessory package with mount plate, bolt-on style prop adapter, and a set of female 3.5mm gold bullet connectors for your ESC.

iPower iBM2212Q Specifications:

KV: 1000
Internal Resistance: 127mΩ
No-Load Current: .5A
Max Current: 13.80A
Continuous Current: 10.8A
Max Watts: 150W
Lipo Cells: 2-3s
Weight: 65g (with hardware)
Dimensions: 28x26mm
Wire length: 75mm
Shaft Diameter: 3.175mm
Recommended Prop: 10×4.5 / 10×4.5R
Recommended ESC: 22A

iPower iBM2212Q 1000KV

iPower Q-series brushless motors are designed specifically for use in multi rotor aircraft. iPower motors are constructed of quality components, making them a smooth, powerful, and efficient motor for your multicopter application. Each 2212 motor features 450mm long motor wires and 3.5mm male gold bullet connectors pre-installed. Also included is an accessory package with mount plate, bolt-on style prop adapter, and a set of female 3.5mm gold bullet connectors for your ESC.

iPower iBM2212Q Specifications:

KV: 1000
Internal Resistance: 127mΩ
No-Load Current: .5A
Max Current: 13.80A
Continuous Current: 10.8A
Max Watts: 150W
Lipo Cells: 2-3s
Weight: 65g (with hardware)
Dimensions: 28x26mm
Wire length: 75mm
Shaft Diameter: 3.175mm
Recommended Prop: 10×4.5 / 10×4.5R
Recommended ESC: 22A

iPeaka SK22A w/SimonK firmware
If you are looking for a reliable, fast esc for your multicopter, look no further.Flashed with the famous SimonK firmware for super fast linear throttle response.All our ESC`s have external oscillators and use only N-Channel FETs.The external oscillator provides more consistent timing signal and steadier motor speeds, while the N-channel FETs have the advantage of lower resistance, less losses and hence more efficiency.Up to 450hz input rate is supported with immediate translation of input PWM duty into motor control.The boot loader is enabled during the initial flash, so each firmware update from now on can be achieved by a USB linker.All ESC`s are tested before and after the firmware update.

Please note:These esc`s DO NOT monitor the battery voltage. A Lipo alarm or a telemetry system should be used for that purpose.

iPeaka SK22A w/SimonK firmware

Features of the iPeaka SK series Speed Controllers include:

• Extremely low output resistance for efficient operation

• 3-stage protection: Low Voltage Cutoff, Over-Heat Protection & Signal Loss

• 3 Start Modes available: Normal, Soft and Very Soft

• Adjustable Throttle Endpoints to match virtually all transmitter models

• Smooth linear throttle operation for precise control

• High RPM capability: 210,000 (2-pole), 70,000 (6-pole), 30,000 (14 pole)

Specifications of the iPeaka SK 22 Amp Speed Controller:

Input Voltage ………………… 6-18.8 VDC, 2-4 Li-Po cells

Input  rate range…………….  50-400Hz

Output Current ………………. 22 Amps Continous, 26 Amps Burst (10 Sec.)

BEC Output …………………. 5.0 Volts at 2 Amps

Dimensions …………………… 35 x 24 x 8 mm

Weight …………………………. 25g

Package included:

  • 4 x iPeaka SK 22A ESC
  • 4 x iBM2212 1000KV
  • 4 x Prop adaptor

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.